In case a router is powered on, where will
the router first search for a valid IOS image to load by default? |
flash memory |
Which two functional parts of the network
are combined to form a collapsed core design as discussed in Cisco Enterprise
Architecture? |
distribution and core layer |
In todays network technology which network
design solution will best extend access layer connectivity to host devices? |
Implementing wireless connectivity |
During the discussion in chapter 6 about
multiarea OSPF, what router that has at least one interface that is attached
to a non-OSPF network? |
ASBR |
What wireless standard consists of various
corporate, national, and international organizations using service provider
cellular access to provide mobile broadband network connectivity? |
Cellular Broadband |
Which security mode is the least secure
choice when a home wireless router is configured? |
WEP |
In chapter 6 which area is referred to as
the "backbone area"? |
. Area 0 |
Which statement is true regarding the use of
PAgP to create EtherChannels? |
It is Cisco proprietary. |
In LAN redundancy which 3 components are
combined to form a bridge ID? |
extended system ID, MAC address, bridge priority |
In Scaling Networks as discussed in chapter
8, If all router Ethernet interfaces in an EIGRP network are configured with
the default EIGRP timers, how long(hold timer) will a router wait by default
to receive an EIGRP packet from its neighbor before declaring the neighbor
unreachable? |
15 sec |
What module consists of the Internet, VPN,
and WAN modules connecting the enterprise with the service provider's network
and also this module extends the enterprise services to remote sites and
enables the enterprise to use Internet and partner resources? |
Enterprise Edge |
During the discussion of OSPF networks on
chapter 6, what is used to facilitate hierarchical routing in OSPF? |
the use of multiple areas |
Referring to the sample result above, a
network specialist has configured eigrp authentication between routers R! and
R2. After there routing tables are received, it is noted that neither router
is receiving eigrp updates. What is a possible cause for this failure? |
The same autonomous system numbers must be used
in the interface configurations of each router. |
What do you called the number of ports
available on a single switch? |
Port density |
During troubleshooting, the administrator
notices the following entry: O*E2 0.0.0.0/0 [110/1] via 192.168.16.3,
00:20:22, Serial0/0/0 What information can be gathered from this output? |
This route is a propagated default route. |
Among the listed below, what advantage do a
WLAN router offers vs. access point? |
Increase in security |
A good example of our learning in chapter 9
is what code in the Cisco IOS 15 image filename C1900-
UNIVERSALK9-MZ.SPA.153-3.M.BIN Indicates that the file is digitally signed by
Cisco? |
SPA |
In a switched LAN environment which RSTP
ports are connected to end devices? |
edge ports |
Where do inter-area route summarization be
performed in an OSPF network? |
ABR |
In OSPFv2 operations which command can be
used to verify the contents of the LSDB in an OSPF area? |
show ip ospf database |
The trunk link between two 2960 switches has
reached its capacity. In understanding of link aggregation, how can this be
addressed in the most economical way? |
Combine physical ports into a high-speed logical
link by configuring EtherChannel. |
Which feature of EIGRP supports AppleTalk,
IP version 4 (IPv4), IP version 6 (IPv6), and Novell Internetwork Packet
Exchange (IPX)? |
Multiple network layer support |
In the understanding of dynamic routing
protocol operations. A scenario where a router has learned three possible
routes that could be used to reach a destination network. One route is from
EIGRP and has a composite metric of 20514560. Another route is from OSPF with
a metric of 782. The last is from RIPv2 and has a metric of 4. Which route or
routes will the router will install in the routing table? |
the EIGRP route |
ASBRs are capable of summarizing which type
of routes? |
External |
The Predator Missile factory network
administrator is checking and troubleshooting an EIGRP problem on a router
and needs to confirm the IP addresses of the devices with which the router
has established adjacency. The retransmit interval and the queue counts for
the adjacent routers also need to be checked. What command will display the
required information? |
Router# show ip eigrp neighbors |
When a range of ports is being configured
for EtherChannel, which mode will configure LACP so that it initiates the
EtherChannel negotiation? |
active |
Among the listed below, which command can be
issued on a router to verify that automatic summarization is enabled? |
Show ip protocols |
Which three statements describe the routing
protocol OSPF as discussed in Chapter 5? 1. It supports VLSM. 2. It is used
to route between autonomous systems. 3. It confines network instability to
one area of the network. 4. It increases routing overhead on the network. 5.
It allows extensive control of routing updates 6. It is simpler to configure
than RIPv2. |
1, 3, 5 |
During the implementation what is the term
used to express the thickness or height of a switch? |
Rack Unit or RU |
Among the 802.11 wireless lan standards what
is the frequency assigned for 802.11ac? |
5Ghz |
The network engineer of 3A Recording
Studiohas added a new router into an established OSPF network. The networks
attached to the new router do not appear in the routing tables of the other
OSPF routers. Given the information in the partial configuration shown below,
what configuration error is causing this problem? Router(config)# router ospf
1 Router(config-router)# network 10.0.0.0 255.0.0.0 area 0 |
The network wildcard mask is configured
improperly. |
Among the 802.11 wireless LAN standards what
is the frequency assigned for 802.11a? |
5Ghz |
What area interconnects with all other OSPF
area types? |
Backbone |
A network administrator of RMS defence
contractor company is configuring an EtherChannel link between switches SW1
and SW2 each switch is located in a different building but just
adjacent to each other by using the command SW1(config-if-range)#
channel-group 1 mode passive. Which command must be used on SW2 to enable
this EtherChannel? |
SW2(config-if-range)# channel-group 1 mode
active |
In which IOS CLI mode must a network
engineer issue the maximum paths command to configure load balancing in
EIGRP? |
router configuration mode |
As discussed in Chapter 2 of Scaling
Networks , which non-proprietary protocol provides router redundancy for a
group of routers which support IPv4 LANs? |
VRRPv2 |
Which of the following is a layer 2 protocol
used to maintain a loop-free network? |
STP |
Among the choices below which command would
you use, If you want to disable STP on a port connected to a server? |
spanning-tree portfast |
Which among the commands below must be
entered on a serial interface of a Cisco router to restore the bandwidth to
the default value of that specific router interface? |
No bandwidth |
What is the default hello timer value for
STP BPDU frames |
2 seconds |
Which among the listed below is an advantage
of PVST+? |
PVST+ optimizes performance on the network
through load sharing. |
Referring to the sample result above, a
network specialist has configured eigrp authentication between routers R! and
R2. After there routing tables are received, it is noted that neither router
is receiving eigrp updates. What is a possible cause for this failure? |
The same autonomous system numbers must be used
in the interface configurations of each router. |
Where are EIGRP successor routes stored? |
in the routing table and the topology table |
The Predator Missile factory network
administrator is checking and troubleshooting an EIGRP problem on a router
and needs to confirm the IP addresses of the devices with which the router
has established adjacency. The retransmit interval and the queue counts for
the adjacent routers also need to be checked. What command will display the
required information? |
Router# show ip eigrp neighbors |
Among the listed below, in deploying
wireless lan what advantage do a WLAN router offers vs. access point?_____+ |
Connect multiple networks |
Standard Electric Company is planning the
implementation of Rapid PVST+ on a production network. How are the Rapid
PVST+ link types determined on the switch interfaces? |
Link types are determined automatically |
Among the listed ip route commands below
which one pertains to propagating a default route? |
Ip route 0.0.0.0 0.0.0.0 192.170.1.2 |
The CCIE of RS Telecom Inc has changed the
router ID on a router that is working in an OSPFv2 environment. What should
the administrator do to reset the adjacencies and use the new router ID? |
Issue the clear ip ospf process privileged mode
command. |
Among the listed below, which serves as a
receipt and is used to obtain a license. It is an 11- digit alphanumeric key
created by Cisco manufacturing and it also defines the Feature Set associated
with it? |
Product Activation Key (PAK) |
Which statement describes a multiarea OSPF
network? |
c. It has a core backbone area with other areas
connected to the backbone area. |
In Scaling Networks as discussed in chapter
8, If all router Ethernet interfaces in an EIGRP network are configured with
the default EIGRP timers, how long(hold timer) will a router wait by default
to receive an EIGRP packet from its neighbor before declaring the neighbor
unreachable? |
15 sec |
In the understanding of dynamic routing
protocol operations. A scenario where a router has learned three possible
routes that could be used to reach a destination network. One route is from
EIGRP and has a composite metric of 20514560. Another route is from OSPF with
a metric of 782. The last is from RIPv2 and has a metric of 4. Which route or
routes will the router will install in the routing table? |
|
Among the 802.11 standards what is the
maximum speed of 802.11g? |
54Mb/s |
The network engineer of RMS University has
configured the hello interval to 15 seconds on an interface of a router that
is running OSPFv2. By default, how will the dead interval on the interface be
affected? |
The dead interval will now be 60 seconds. |
What is the purpose of HSRP in switching
environment? |
It provides a continuous network connection when
a router fails. |
In understanding link aggregation which
protocol is an IEEE standard, it can be used to facilitate EtherChannels in
multivendor environments? |
LACP |
Using PagP as range of ports to be configured
as etherchannel, which mode will form the bundled channel only if the port
receives PAgP packets from another device? |
auto |
As discussed in chapter 7, when an
EIGRP-enabled router uses a password to accept routes from other
EIGRP-enabled routers, which mechanism is used? |
EIGRP authentication |
In link aggregation configuration, which
command will initiate EtherChannel interface configuration mode? |
interface port-channel interface-identifier |
Which among the listed below are two types
of spanning tree protocols can cause suboptimal traffic flows because they
assume only one spanning-tree instance for the entire bridged network? |
STP & RSTP |
In etherchannel configuration what is a
requirement to configure a trunking EtherChannel between two switches? |
The allowed range of VLANs must be the same on
both switches |
What wireless LAN technology that operates
in the range of a few hundred feet? |
WLAN |
In wireless LAN technology and standards
what classification do Bluetooth belongs? |
WPAN |
At the start with the Cisco IOS Software
Release 15.0, which license is a prerequisite for installing additional
technology pack licenses? |
IPBase |
In configuring link aggregation an
EtherChannel link using LACP was formed between two switches, S1 and S2. While
verifying the configuration, which mode combination could be utilized on both
switches? |
S1-passive and S2-active |
Refer to the exhibit. In RMS Robotics
Industries network, Four routers are connected to an Ethernet LAN segment and
are configured to run OSPFv3. However, none of the routers are receiving
routing updates. What is the cause of the problem? |
All of the routers have an OSPFv3 interface
priority of 0. |
In scalable hierarchical network design,
what is the design model layer that provides a high-speed backbone link
between dispersed networks? |
Core Layer |
As a newly hired network administrator of
RMS Telecom Corporation you have been asked to implement EtherChannel on the
corporate network. What does this configuration consist of? |
grouping multiple physical ports to increase
bandwidth between two switches |
Among the listed network subnet below, which
two networks are part of the summary route 192.168.32.0/22? 1.
192.168.36.0/24 2. 192.168.33.0/24 3. 192.168.35.0/24 4. 192.168.31.0/24 5.
192.168.37.0/24 6. 192.168.38.0/24 |
2 & 3 |
During the troubleshooting in RPN Radio/TV
Network , there are 2 routers, R1 and R2, have established an EIGRP neighbor
relationship, but still ip connectivity problem still persist. Which issue
could be causing this problem? |
An access list that is blocking the
advertisements from othernetworks was configured in each or both routers |
In Chapter 6, what OSPF LSA type is used to
inform routers of the router ID of the DR in each multiaccess network in an
OSPF area? |
|
A new network specialist has been asked to
verify the metrics that are used by EIGRP on a Cisco device. Which two EIGRP
metrics are measured by using static values on a Cisco device? |
Bandwidth & delay |
In understanding wireless LAN technology and
standards, what is the maximum data rate specified for IEEE 802.11g WLANs? |
54Mbps |
In understanding IOS system image files what
statement describes a Cisco IOS image with the “universalk9_npe” designation
for Cisco ISR G2 routers? |
It is an IOS version that, at the request of
some countries, removes any strong cryptographic functionality |
In understanding Cisco IOS image which
statement describes a difference between the IOS 15.0 extended maintenance
release and a standard maintenance release? |
The standard maintenance release enables faster
IOS feature delivery than the extended maintenance release does. |
When a customer purchases a Cisco IOS 15.0
software package, what serves as the receipt for that customer and is used to
obtain the license as well? |
Product Activation Key |
A CCNA network administrator configures a
router with the command sequence: R1(config)# boot system
tftp://c1900-universalk9-mz.SPA.152-4.M3.bin R1(config)# boot system
rom What is the effect of the command sequence? |
The router will load IOS from the TFTP server.
If the image fails to load, it will load the IOS image from ROM. |
The PRD company network engineer is
upgrading the Cisco IOS image on a Cisco ISR 4000 series. What command could
the engineer use to verify the total amount of flash memory as well as how
much flash memory is currently available? |
show flash0: |
As discussed in this chapter, beginning with
the Cisco IOS Software Release 15.0, which license is a prerequisite for
installing additional technology pack licenses? |
IPBase |
In understanding IOS system image files
which IOS 12.4 software package integrates full features, including voice,
security, and VPN capabilities, for all routing protocols? |
Advanced Enterprise Services |
As discussed in chapter 9 of Scaling
Networks what is the major release number in the IOS image name
c1900-universalk9-mz.SPA.152-3.T.bin? |
15 |
The client of a networking company requires
VPN connectivity for workers who must travel frequently. To support the VPN
server, the customer router must be upgraded to a new Cisco IOS software
version with the Advanced IP Services feature set. What should the field
engineer do before copying the new IOS to the router? |
Issue the show version and the show flash
commands to ensure that the router has enough memory and file space to
support the new IOS image. |
As discussed in chapter 7 as one of the
EIGRP concepts what is the purpose of using protocoldependent modules in
EIGRP? |
to accommodate routing of different network layer
protocols |
During network troubleshooting in MAX
Industries factory 2 routers, R1 and R2, have established an EIGRP neighbor
relationship, but there is still a connectivity problem. Which issue could be
causing this problem? |
An access list that is blocking the
advertisements from other networks was configured in each or both routers |
During EIGRP operation which two EIGRP
packet types are sent with reliable delivery? |
Hello & Ack |
Among the listed below which is a feature of
EIGRP? |
Load balancing |
During the network troubleshooting in RMS
Hospital the network administrator notice an EIGRP problem on a router and
needs to confirm the IP addresses of the devices with which the router has
established adjacency. The retransmit interval and the queue counts for the
adjacent routers also need to be checked. What command will display the
required information? |
c |
A network engineer in ABC Enterprise is
asked to stop auto route summary in EIGRP, which command you will use to
prevent auto summary? |
c |
Discussed in chapter 9, what code in the
Cisco IOS 15 image filename C1900-UNIVERSALK9- MZ.SPA.153-3.M.BIN Indicates
that the file is digitally signed by Cisco? |
SPA |
During summarization configuration what
address and wild card mask can be used to enable EIGRP for only the subnet
192.168.100.192 255.255.255.192? |
192.168.100.192 0.0.0.63 |
A student uses a laptop to upload an
assignment to a file server. Which wireless frame type did the laptop send to
locate and associate with the campus access point? |
management frame |
When a home wireless AP is being configured,
_____ is used to identify the wireless network name? |
SSID |
In understanding link aggregation what is a
best practice to use before beginning an EtherChannel implementation? |
Shut down each of the affected interfaces. |
In wireless LAN security what is an
advantage of SSID cloaking? |
Clients will have to manually identify the SSID
to connect to the network. |
During which stage of establishing
connectivity between a WLAN client and an AP does the client learn the MAC
address of the AP? |
association |
A network specialist of PRS Industries is
troubleshooting an OSPFv2 network and discovers that two routers connected by
a point-to-point WAN serial link are not establishing an adjacency. The OSPF
routing process, network commands and area ID are all confirmed as correct,
and the interfaces are not passive. Testing shows that the cabling is
correct, that the link is up, and pings between the interfaces are
successful. What is most likely the problem? |
The subnet masks on the two connected serial
interfaces do not match. |
The use of PAgP to create EtherChannels is
discussed in link aggregation chapter as part of Scaling Network. Which
statement below as discussed in this course is true about PagP? |
It is a Cisco Proprietary |
Which IEEE wireless standard is known as
WiGig and operates using a tri-band solution in the 2, 4, 5, and 60 GHz
ranges? |
802.11ad |
Which statement describes an EtherChannel
implementation? |
A trunked port can be part of an EtherChannel
bundle. |
Among the 802.11 standards what is the
frequency assigned for 802.11g? |
2.4Ghz |
In specific 802.11 wireless lan standard
what maximum speed can 802.11n reached? |
600Mbps |
Understanding scaling networks, which
feature supports higher throughput in switched networks by combining multiple
switch ports? |
Link aggregation |
A newly hired network engineer has been
instructed to implement EtherChannel in a corporate network. What does this
configuration consist of? |
grouping multiple physical ports to increase
bandwidth between two switches |
Understanding EtherChannel technology, what
is an advantage of using LACP? |
allows automatic formation of EtherChannel links |
Referring to the diagram below of
Chooks-to-Go office. Which switching technology would allow each access layer
switch link to be aggregated to provide more bandwidth between each Layer 2
switch and the Layer 3 switch? |
EtherChannel |
The trunk link between two 2960 switches has
reached its capacity. How can solve this problem in the most economical way? |
Combine physical ports into a high-speed logical
link by configuring EtherChannel. |
In AP technology which type of management
frame may regularly be broadcast by an AP? |
beacon |
In Cisco APs that operate in a home
environment and Cisco APs that operate in a corporate environment what is the
most likely advantage of corporate access points? |
Many corporate AP models can operate in either
autonomous mode or controller-based mode. |
As discussed in link aggregation what are
two requirements to be able to configure an EtherChannel between two
switches? |
All the interfaces need to work at the same speed
& need to be working in the same duplex mode. |
In wireless LAN standards what wireless LAN
technology that is an IEEE 802.15 WPAN standard; uses a device pairing
process to communicate over distance up to .05 mile (100m)? |
Bluetooth |
It is known as WiGig and operates using a
tri-band solution in the 2.4, 5, and 60 GHz ranges in IEEE wireless standard? |
802.11ad |
Which security mode is the least secure
choice when a home wireless router is configured. It is also the first
security mode used for wireless? |
WEP |
In specific 802.11 wireless lan standard
what frequency band is assigned for 802.11a? |
5Ghz |
Using LACP, besides of being a multivendor
protocol which among the listed below describes as it advantage? |
allows automatic formation of EtherChannel links |
In Scaling Networks course, link aggregation
should be implemented at which layer of the hierarchical network? |
Access, distribution, and core |
A newly hired certified network engineer of
RMS Industries is troubleshooting a switch and wants to verify if it is a
root bridge. Which of the following listed below is the right command to
display the correct information? |
. show spanning-tree |
In RMS University, the network admin is
trying to add a new router into an established OSPF network. The network
attached to the new router do not appear in the routing tables of the other
OSPF routers. Given the information in the partial configuration shown below,
what configuration error is causing this problem? Router(config)# router ospf
1 Router(config-router)# network 10.0.0.0 255.0.0.0 area 0 |
The network wildcard mask is configured
improperly. |
An airline company has recently implemented
an 802.11n wireless network. Some users are complaining that the wireless
network is too slow. Which solution is the best method to enhance the
performance of the wireless network? |
Split the traffic between the 2.4 GHz and 5 GHz
frequency bands |
This wireless attack comes from an old term
called war dialing, where people would dial random phone numbers in search of
modems. It is basically people driving around looking for vulnerable APs to
attack. What wireless attack is this? |
War driving |
A router with its interfaces attached to
multiple areas is called ABR |
TRUE |
Among the listed below what organization
that set or influence WLAN standards? |
IEEE |
What is the frequency range of the IEEE
802.11b standard as discussed in wireless LAN standards? |
2.4GHz |
Using 2 switches, which PAgP mode
combination will establish an EtherChannel? |
switch 1 set to desirable; switch 2 set to
desirable. |
During the wireless implementation planning
what type of wireless antenna is best suited for providing coverage in large
open spaces, such as hallways or large conference rooms? |
In wireless topologies, Yagi is a type of
directional antenna that can be used in long distance Wi-Fi networking. |
When a range of ports is being configured
for EtherChannel by the use of PAgP, which mode will form the bundled channel
only if the port receives PAgP packets from another device? |
auto |
What type of wireless attack that uses the
method by flooding an AP with deauthentication frames? |
Jamming |
A network administrator discovers a visitor
is trying to flood an AP with deauthentication frames. After some
interrogation the security department finds out he is from a competitor
company. The attack the visitor used is called jamming. |
TRUE |
In configuring OSPF authentication which two
pieces of information are used by the OSPF MD5 algorithm to generate a
signature? |
secret key & OSPF message |
A certified network engineer of a new
startup company is configuring an EtherChannel link between switches SW1 and
SW2 by using the command SW2(config-if-range)# channel-group 1 mode passive.
Which command must be used on SW1 to enable this EtherChannel? |
SW1(config-if-range)# channel-group 1 mode
active |
As discussed in wireless LAN technologies
and standards, what wireless LAN technology that is an IEEE 802.16 WWAN
standard that provides wireless broadband access of up to 30mi (50km)? |
WIMAX |
Which type of wireless antenna is best
suited for providing coverage in large open spaces, such as hallways or large
conference rooms? |
Omnidirectiona |
Refer to the exhibit shown. What command
statement must be issued to complete the configuration at R1 for multiarea
OSPF. |
network 192.168.10.128 0.0.0.127 area 1 |
In understanding OSPF concepts which
parameter or parameters are used to calculate OSPF cost in Cisco routers? |
Bandwidth |
In wireless LAN technologies what wireless
LAN technology that operates in the range of a few hundred feet? |
WLAN |
Based on the discussion in this chapter,
which command syntax will initiate EtherChannel interface configuration mode? |
interface port-channel interface-identifie |
Which statement is correct as discussed in
this chapter regarding the use of PAgP to create EtherChannels? |
It is Cisco proprietary. |
In implementing EtherChannel technology,
which PAgP mode combination will establish an EtherChannel? |
switch 1 set to desirable; switch 2 set to
desirable. |
In single-area OSPF concepts which parameter
would you tune to affect the selection of a static route as a backup, when a
dynamic protocol is also being used? |
administrative distance |
In implementation of OSPF network what
command pertains to propagating a default route? |
Ip route 0.0.0.0 0.0.0.0 192.200.1.2 |
A network link connected to a switch went
down. How long can it take for a network using spanning tree topology to
converge again after a topology change? |
up to 50 seconds |
A network specialist of PRS Industries is
troubleshooting an OSPFv2 network and discovers that two routers connected by
a point-to-point WAN serial link are not establishing an adjacency. The OSPF
routing process, network commands and area ID are all confirmed as correct,
and the interfaces are not passive. Testing shows that the cabling is
correct, that the link is up, and pings between the interfaces are
successful. What is most likely the problem? |
The subnet masks on the two connected serial
interfaces do not match. |
A network expert discovers a rogue AP in the
network. The rogue AP is capturing traffic and then forwarding it on to the
legitimate AP. What type of attack is this? |
Man in the middle |
In troubleshooting OSPF issues which command
is used to verify that OSPF is enabled and also provides a list of the
networks that are being advertised by the network? |
show ip protocols |
What happens when a router has two network
statements in different areas? |
It becomes ABR |
Why do OSPF serial interfaces usually
require manual bandwidth configuration? |
OSPF uses the bandwidth value to compute routes
for its routing table. |
During checking of routing table, a network
engineer notices the following entry: O*E2 0.0.0.0/0 [110/1] via
192.168.16.3, 00:20:22, Serial0/0/0 What information can be gathered from
this output |
This route is a propagated default route |
This always appear in certification exams so
remember this, which parameter or parameters are used to calculate OSPF cost
in Cisco routers? |
Bandwidth |
Which two pieces of information are used by
the OSPF MD5 algorithm to generate a signature? |
Secret key & OSPF message |
When OSPFv2 neighbors are establishing
adjacencies, in which state do they elect a DR and BDR router? |
Two-Way state |
In OSPF configuration understanding which
parameter would you tune to affect the selection of a static route as a
backup, when a dynamic protocol is also being used? |
administrative distance |
In OSPF networks discussion what router that
has at least one interface that is attached to a non-OSPF network? |
ASBR |
Refer to the exhibit shown above. A
certified network administrator is troubleshooting the four routers that are
connected to an Ethernet LAN segment and are configured to run OSPFv3.
However, none of the routers are receiving routing updates. What is the cause
of the problem? |
All of the routers have an OSPFv3 interface
priority of 0. |
In understanding multiarea OSPF network
which statement describes a multiarea OSPF network? |
. It has a core backbone area with other areas
connected to the backbone area. |
As discussed in link state advertisement
which two statements correctly describe OSPF type 3 LSAs? 1. Type 3 LSAs are
used to update routes between OSPF areas. 2. Type 3 LSAs are known as router
link entries . 3. Type 3 LSAs are used for routes to networks outside the
OSPF autonomous system . 4. Type 3 LSAs are known as autonomous system
external LSA entries. 5. Type 3 LSAs are generated without requiring a full
SPF calculation. |
1 & 5 |
OSPF type 2 LSA messages are only generated
by the DR router to advertise routes in multiaccess networks. |
TRUE |
During the investigation of routing table,
the network administrator notices the following entry: O*E2 0.0.0.0/0 [110/1]
via 192.168.10.3, 00:20:22, Serial0/0/0 What information can be gathered from
this output? |
This route is a propagated default route |
During the checking a routing table, a
network specialist notices the following entry: O*E2 0.0.0.0/0 [110/1] via
192.168.16.3, 00:20:22, Serial0/0/0 What information can be gathered from
this output? |
This route is a propagated default route. |
Which 3 features are OSPF routing protocol? |
Converge quickly, Identify the best route by the
use of cost & before exchanging routing information, OSPF routers find
out neighbors. |
Which area is referred to as the
"backbone area"? |
. Area 0 |
Which three statements describe the routing
protocol OSPF? 1. It supports VLSM. 2. It is used to route between autonomous
systems. 3. It confines network instability to one area of the network. 4. It
increases routing overhead on the network. 5. It allows extensive control of
routing updates 6. It is simpler to configure than RIPv2. |
1, 3, 5 |
Which show command is used to display the
collection of OSPF link states? |
show ip ospf database |
As discussed in this chapter which statement
is true regarding OSPF multi-area adjacencies? |
One logical interface will be a primary link,
and the other configured as a secondary link; the secondary link will be
established as an unnumbered point-to-point interface. |
A certified network administrator of Gilas
Medical Hospital has just changed the router ID on a router that is working
in an OSPFv2 environment. What should the administrator do to reset the
adjacencies and use the new router ID |
Issue the clear ip ospf process privileged mode
command. |
6 |
1 & 5 |
In network troubleshooting, which command
can be issued on a router to verify that automatic summarization is enabled? |
show ip protocol |
What does an O IA routing table entry mean? |
Inter-area route |
If all OSPF routers in a single area are
configured with the same priority value, what value does a router use for the
OSPF router ID in the absence of a loopback interface? |
. the highest IP address among its active
interfaces |
In scaling networks what command pertains to
propagating a default route? |
Ip route 0.0.0.0 0.0.0.0 192.200. |
What routerhas all of its interfaces in the
same area and have identical LSDBs. |
. Internal Router |
8. In OSPF discussions what is used to
facilitate hierarchical routing in OSPF? |
the use of multiple areas |
A certified network administrator of RMS
Company has just changed the router ID on a router that is working in an
OSPFv2 environment. What should the administrator do to reset the adjacencies
and use the new router ID? |
Issue the clear ip ospf process privileged mode
command. |
During checking of routing table, a network
engineer notices the following entry: O*E2 0.0.0.0/0 [110/1] via
192.168.16.3, 00:20:22, Serial0/0/0 What information can be gathered from
this output? |
This route is a propagated default route |
In troubleshooting OSPF issues why do OSPF
serial interfaces usually require manual bandwidth configuration? |
OSPF uses the bandwidth value to compute routes
for its routing table. |
What routing table descriptor is used to
identify OSPF summary networks that originate from an ABR? |
O IA |
In link state advertisement the type 1 LSAs
are also refered to as: |
Router link entries |
A network administrator is implementing OSPF
in a portion of the network and must ensure that only specific routes are
advertised via OSPF. Which network statement would configure the OSPF process
for networks 192.168.4.0, 192.168.5.0, 192.168.6.0, and 192.168.7.0, now
located in the backbone area, and inject them into the OSPF domain? |
c |
As discussed in Scaling Network course when
OSPFv2 neighbors are establishing adjacencies, in which state do they elect a
DR and BDR router? |
Two-Way state |
The backbone area interconnects with all
other OSPF area types. |
TRUE |
During the testing and troubleshooting, the
senior network administrator investigates and notices the following entry:
O*E2 0.0.0.0/0 [110/1] via 192.168.16.3, 00:20:22, Serial0/0/0 What
information can be gathered from this output? |
This route is a propagated default route. |
Refer to the series of ip addresses below. A
network specialist has been asked to summarize the networks shown in the
exhibit as part of a multiarea OSPF implementation. All addresses are using a
subnet mask of 255.255.255.0. What is the correct summarization for these
eight networks? 10.0.4.0 10.0.8.0
10.0.5.0 10.0.9.0
10.0.6.0 10.0.10.0
10.0.7.0 10.0.11.0 |
10.0.0.0 255.255.240.0 |
Which three statements describe the routing
protocol OSPF? 1. It supports VLSM. 2. It is used to route between autonomous
systems. 3. It confines network instability to one area of the network. 4. It
increases routing overhead on the network. 5. It allows extensive control of
routing updates 6. It is simpler to configure than RIPv2. |
1, 3, 5 |
An ASBR generates type 5 LSAs for each of
its external routes and floods them into the area that it is connected to. |
TRUE |
Refer to the network topology diagram above.
A certified network expert has configured the OSPF timers to the values that
are shown in the graphic. What is the result of having those manually
configured timers? |
The R1 dead timer expires between hello packets
from R2 |
During router configuration what OSPF LSA
type is used to inform routers of the router ID of the DR in each multiaccess
network in an OSPF area? |
type 2 |
Referring to the test result shown above.
Given the output for this command, if the router ID has not been manually
set, what router ID will OSPF use for this RouterD? |
172.16.5.1 |
As discussed in this chapter multiarea OSPF
what OSPF LSA type is used to inform routers of the router ID of the DR in
each multiaccess network in an OSPF area? |
type 2 |
In understanding concepts of OSPF which
three statements describe the routing protocol OSPF? 1. It supports VLSM. 2.
It is used to route between autonomous systems. 3. It confines network
instability to one area of the network. 4. It increases routing overhead on
the network. 5. It allows extensive control of routing updates 6. It is
simpler to configure than RIPv2. |
1, 3, 5 |
A CCIE network administrator is verifying a
multi-area OSPF configuration by checking the routing table on a router in
area 1. The administrator notices a route to a network that is connected to a
router in area 2. Which code appears in front of this route in the routing
table within area 1? |
O IA |
The network specialist has manually
configured the hello interval to 15 seconds on an interface of a router that
is running OSPFv2. By default, how will the dead interval on the interface be
affected? |
The dead interval will now be 60 seconds. |
Which command statement below will a network
engineer issue to verify the configured hello and dead timer intervals on a
point-to-point WAN link between two routers that are running OSPFv2? |
show ip ospf interface serial 0/0/0 |
As discussed in our topic Scaling Networks
chapter 6,which area is referred to as the "backbone area"? |
Area 0 |
Which command will a network engineer issue
to verify the configured hello and dead timer intervals on a point-to-point
WAN link between two routers that are running OSPFv2? |
show ipospf interface serial 0/0/0 |
A certified network administrator is trying
to add a new router into an established OSPF network. The networks attached
to the new router do not appear in the routing tables of the other OSPF
routers. Given the information in the partial configuration shown below, what
configuration error is causing this problem? |
The network wildcard mask is configured
improperly. |
In this chapter, which two types of spanning
tree protocols can cause sub-optimal traffic flows because they assume only
one spanning-tree instance for the entire bridged network? |
STP & RSTP |
Why would a network administrator of RMS
Defence Contractor company issue the show cdp neigbors command on a router
especially if a network problem occurs? |
To display device ID and other information about
directly connected Cisco devices |
Which two networks are part of the summary
route 192.168.32.0/22? (Choose a letter) |
2 & 3 |
As discussed in Chapter 2, what do you
called a design methodology for building networks in three layers including
access, distribution, and core. |
hierarchical network |
As discussed in link state advertisement
which two statements correctly describe OSPF type 3 LSAs? 1. Type 3 LSAs are
used to update routes between OSPF areas. 2. Type 3 LSAs are known as router
link entries . 3. Type 3 LSAs are used for routes to networks outside the
OSPF autonomous system . 4. Type 3 LSAs are known as autonomous system
external LSA entries. 5. Type 3 LSAs are generated without requiring a full
SPF calculation. |
1 & 5 |
As shown from the network diagram above, the
command “show ipv6 route can be issued on router R2 to verify the propagation
of static default router from R1 to R2" Why is MD5 authentication is
more secure than simple authentication of OSPF updates? |
MD5 does not send the password to the neighbor
router. |
Which describes a multiarea OSPF network? |
It has a core backbone area with other areas
connected to the backbone area. |
A network administrator of an international
herbal company is verifying a multi-area OSPF configuration by checking the
routing table on a router in area 1. The administrator notices a route to a
network that is connected to a router in area 2. Which code appears in front
of this route in the routing table within area 1? |
O IA |
Divides the network into functional
components while still maintaining the core, distribution, and access layers
of the three-layer model as discussed in chapter 2 LAN Redundancy? |
Cisco Enterprise Architecture |
A router that has at least one interface
that is attached to a non-OSPF network is called ASBR. |
TRUE |
Refer to the series of ip addresses below. A
network specialist has been asked to summarize the networks shown in the
exhibit as part of a multiarea OSPF implementation. All addresses are using a
subnet mask of 255.255.255.0. What is the correct summarization for these
eight networks? 10.0.4.0 10.0.8.0
10.0.5.0 10.0.9.0 10.0.6.0
10.0.10.0 10.0.7.0 10.0.11.0 |
10.0.0.0 255.255.240.0 |
Which network design solution below in the
current technology today will extend access layer connectivity to user
devices? |
Wireless connectivity implementation |
Among the choices listed below, which port
state will switch ports ?immediately transition to when configured for
PortFast |
Forwarding |
7. Which two networks are part of the
summary route 192.168.32.0/22? (Choose a letter) |
2 & 3 |
Refer to the test result above. These two
routers are configured to run OSPFv3 but they are not forming a neighbor
adjacency. What is the cause of the problem? |
The routers are configured with the same router
ID. |
Which is the default STP operation mode on
Cisco Catalyst switches? |
PVST+ |
A connection to a switch went down suddenly,
how long can it take for a network using RSTP to converge again after a
topology change? |
6sec |
As shown in the exhibit below, which
protocol information is being displayed in the output? |
GLBP |
In verifying multiarea OSPF which command
can be used to verify the contents of the LSDB in an OSPF area? |
show ip ospf database |
A network administrator is implementing OSPF
in a portion of the network and must ensure that only specific routes are
advertised via OSPF. Which network statement would configure the OSPF process
for networks 192.168.4.0, 192.168.5.0, 192.168.6.0, and 192.168.7.0, now
located in the backbone area, and inject them into the OSPF domain? |
c |
10. Which three steps in the design and implementation
of a multiarea OSPF network are considered planning steps? (Choose a letter) |
2, 4 & 5 |
In this chapter, which is a characteristic
of a Layer 2 loop? |
Broadcast frames are forwarded back to the
sending switch |
In managing cisco devices, which two
requirements must always be met to use in-band management to configure a
network device? |
at least one network interface that is connected
and operational & Telnet, SSH, or HTTP access to the device |
The network engineer of Stark Industries has
manually configured the hello interval to 15 seconds on an interface of a
router that is running OSPFv2. By default, how will the dead interval on the
interface be affected? |
The dead interval will now be 60 seconds. |
Observe the given output below. A certified
network engineer is troubleshooting host connectivity on a LAN that uses a
first hop redundancy protocol. Which IPv4 gateway address should be
configured on the host? |
192.168.2.100 |
Referring to the exhibit, the command “show
ipv6 route can be issued on router R2 to verify the propagation of a static
default router from R1 to R2" As discussed in this chapter why is MD5
authentication is more secure than simple authentication of OSPF
updates?a |
MD5 does not send the password to the neighbor
router. |
If you want to disable STP on a port
connected to a server, which command would you use? |
spanning-tree portfast |
A CCIE network administrator is verifying a
multi-area OSPF configuration by checking the routing table on a router in
area 1. The administrator notices a route to a network that is connected to a
router in area 2. Which code appears in front of this route in the routing
table within area 1? |
O IA |
In terms of network reliability, the ability
of a network to be up most of the time. Sometimes referred to as 99.999, or
"five nines". |
Reliability |
A certified network administrator is trying
to add a new router into an established OSPF network. The networks attached
to the new router do not appear in the routing tables of the other OSPF
routers. Given the information in the partial configuration shown below, what
configuration error is causing this problem? Router(config)# router ospf 1
Router(config-router)# network 10.0.0.0 255.0.0.0 area 0 |
The network wildcard mask is configured
improperly |
In EIGRP operation if all router Ethernet
interfaces in an EIGRP network are configured with the default EIGRP timers,
how long will a router wait by default to receive an EIGRP packet from its
neighbor before declaring the neighbor unreachable? |
15 seconds |
In understanding basic features and
operation of EIGRP what is the EIGRP metric? |
K-values |
In understanding of chapter 7 EIGRP uses the
dual algorithm for finding shortest path? |
TRUE |
In today's current switch technology, Which
statement describes a characteristic of Cisco Meraki switches? |
They are cloud-managed access switches that
enable virtual stacking of switches. |
Among the choices below, which protocol
specified by RFC 2281 provides network redundancy for IP networks, ensuring
that user traffic immediately and transparently recovers from first-hop
failures in network edge devices or access circuits? |
HSRP |
As discussed in chapter 1, the duplication
of devices, services, or connections so that, in the event of a failure, the
redundant devices, services , or connections can perform the work of those
that failed. |
Redundancy |
Access Layer is a design model layer that
provides connectivity for the users. |
TRUE |
How many switches in a network must be
running STP or RSTP in order to avoid broadcast storms? |
At least one in each loop |
During the discussion in this chapter, what
is a characteristic of in-band device management? |
It is used to monitor and make configuration
changes to a network device over a network connection. |
In networking term, port density refers to
the number of ports available on a single switch. |
TRUE |
In networking world, "Rack unit"
is the term used to express the thickness or height of a switch. |
TRUE |
How much traffic for a 12port gigabit switch
capable of generating when operating at full wire speed? |
12 Gb/s, by providing full bandwidth to each
port |
In FHRP operation, two or more routers are
represented as a single virtual router. |
TRUE |
In OSPF discussions what is used to
facilitate hierarchical routing in OSPF? |
the use of multiple areas |
A certified network expert is configuring a
LAN with a redundant first hop to make better use of the available network
resources. Which protocol should the engineer implement? |
GLBP |
Core Layer is a design model layer that
forwards traffic from/to different local networks |
FALSE |
If you are a network design engineer, which
type of router would an enterprise use to allow customers to access content
anytime and anyplace, regardless of whether they are at home or work? |
Network edge routers |
What is the useof in-band device management
and how it is done? |
It is used to monitor and make configuration
changes to a network device over a network connection. |
Which among the listed below are the 2
functional parts of the network that can be combined to form a collapsed core
design in Cisco Enterprise Architecture? |
Distribution and core layer |
A certified network administrator is trying
to add a new router into an established OSPF network. The networks attached
to the new router do not appear in the routing tables of the other OSPF
routers. Given the information in the partial configuration shown below, what
configuration error is causing this problem? Router(config)# router ospf 1
Router(config-router)# network 10.0.0.0 255.0.0.0 area 0 |
The network wildcard mask is configured
improperly. |
A CCIE network administrator is verifying a
multi-area OSPF configuration by checking the routing table on a router in
area 1. The administrator notices a route to a network that is connected to a
router in area 2. Which code appears in front of this route in the routing
table within area 1? |
O IA |
A certified wireless professional wishes to
extend the range of the existing IEEE 802.11n network without changing the
AP. What can the administrator do to accomplish this? |
Deploy a Wi-Fi Repeater. |
Which three steps in the design and
implementation of a multiarea OSPF network are considered planning steps?
(Choose a letter) |
2, 4 & 5 |
In understanding Cisco IOS image which
statement describes a difference between the IOS 15.0 extended maintenance
release and a standard maintenance release? |
They consist of two separate parallel trains. |
Which switchport mode puts the interface
into permanent nontrunking ? |
switchport mode dynamic auto |
Which type of router would an enterprise use
to allow customers to access content anytime and anyplace, regardless of
whether they are at home or work? |
network edge routers |
A PC is to access a web server on another
network. Which inter-VLAN method will provide the highest bandwidth at Layer
3 and also provide a default gateway for the PC? |
multilayer switch with routing enabled |
An administrator is investigating a failure
on a trunk link between a Cisco switch and a switch from another vendor.
After a few show commands, the administrator notices that the the switches
are not negotiating a trunk. What is a probable cause for this issue? |
Switches from other vendors do not support DTP. |
A certified wireless professional wishes to
extend the range of the existing IEEE 802.11n network without changing the
AP. What can the administrator do to accomplish this? |
Deploy a Wi-Fi Repeater. |
The PRD company network engineer is
upgrading the Cisco IOS image on a Cisco ISR 4000 series. What command could
the engineer use to verify the total amount of flash memory as well as how
much flash memory is currently available? |
show version |
How much traffic is a 48-port gigabit switch
capable of switching when operating at full wire speed? |
48 Gb/s, by providing full bandwidth to each
port |
Which sentence correctly describes the SVI
inter-VLAN routing method? |
An SVI is needed for each VLAN. |
Understanding multiarea OSPF what is one
advantage of using multiarea OSPF? |
It enables multiple routing protocols to be
running in a large network. |
What type of wireless attack that uses the
method by flooding an AP with deauthentication frames? |
Jamming |
Which switchport mode makes the interface
able to convert the link to a trunk |
switchport mode access |
In understanding IOS system image files
which IOS 12.4 software package integrates full features, including voice,
security, and VPN capabilities, for all routing protocols? |
Advanced Enterprise Services |
Which network design solution will best
extend access layer connectivity to host devices? |
implementing wireless connectivity |
In understanding IOS system image files what
statement describes a Cisco IOS image with the “universalk9_npe” designation
for Cisco ISR G2 routers? |
It is an IOS version that provides only the
IPBase feature set. |
Discussed in chapter 9, what code in the
Cisco IOS 15 image filename C1900-UNIVERSALK9-MZ.SPA.153-3.M.BIN Indicates
that the file is digitally signed by Cisco? |
SPA |
10. Which three steps in the design and
implementation of a multiarea OSPF network are considered planning steps?
(Choose a letter) |
2, 3 & 4 |
Which technology is required when switched
networks are designed to include redundant links? |
Spanning Tree Protocol |
A new network specialist has been asked to
verify the metrics that are used by EIGRP on a Cisco device. Which two EIGRP
metrics are measured by using static values on a Cisco device? |
Bandwidth & delay |
A CCNA network administrator configures a
router with the command sequence: R1(config)# boot system
tftp://c1900-universalk9-mz.SPA.152-4.M3.bin R1(config)# boot system rom What
is the effect of the command sequence? |
The router will load IOS from the TFTP server.
If the image fails to load, it will load the IOS image from ROM. |
A network problem occurs suddenly, what is
the initial approach that should be used to troubleshoot a broadcast storm in
a switched network? |
Manually remove redundant links in the switched
network. |
During the network troubleshooting in RMS
Hospital the network administrator notice an EIGRP problem on a router and
needs to confirm the IP addresses of the devices with which the router has
established adjacency. The retransmit interval and the queue counts for the
adjacent routers also need to be checked. What command will display the
required information? |
c |
In understanding of this chapter which
characteristic describes both ABRs and ASBRs that are implemented in a
multiarea OSPF network? |
They are required to reload frequently and
quickly in order to update the LSDB. |
A network expert discovers a rogue AP in the
network. The rogue AP is capturing traffic and then forwarding it on to the
legitimate AP. What type of attack is this? |
Man in the middle |
A network engineer in ABC Enterprise is
asked to stop auto route summary in EIGRP, which command you will use to
prevent auto summary? |
c |
During the upgrade of IOS system image, a
router is powered on, where will the router first search for a valid IOS
image to load by default? |
flash memory |
As discussed in chapter 9 of Scaling
Networks what is the major release number in the IOS image name c1900-universalk9-mz.SPA.152-3.T.bin? |
52 |
The client of a networking company requires
VPN connectivity for workers who must travel frequently. To support the VPN
server, the customer router must be upgraded to a new Cisco IOS software
version with the Advanced IP Services feature set. What should the field
engineer do before copying the new IOS to the router? |
Set the router to load the new IOS image file
directly from the TFTP server on the next reboot. |
A network link connected to a switch went
down. How long can it take for a network using spanning tree topology to
converge again after a topology change? |
up to 50 seconds |
ASBRs are capable of summarizing which type
of routes? |
External |
What is the purpose of VTP? |
It provides centralized management of VLANs in a
multi-switch environment. |
A remote class room can successfully access
video-intensive streaming lectures via wired computers. However, when an
802.11n wireless access point is installed and used with 25 wireless laptops
to access the same lectures, poor audio and video quality is experienced.
Which wireless solution would improve the performance for the laptops? |
Add another access point. |
Which feature could be used in a network
design to increase the bandwidth by combining multiple physical links into a
single logical link? |
EtherChannel |
A network specialist of PRS Industries is
troubleshooting an OSPFv2 network and discovers that two routers connected by
a point-to-point WAN serial link are not establishing an adjacency. The OSPF
routing process, network commands and area ID are all confirmed as correct,
and the interfaces are not passive. Testing shows that the cabling is
correct, that the link is up, and pings between the interfaces are
successful. What is most likely the problem? |
The subnet masks on the two connected serial
interfaces do not match. |
When a customer purchases a Cisco IOS 15.0
software package, what serves as the receipt for that customer and is used to
obtain the license as well? |
End User License Agreement |
8. In OSPF discussions what is used to
facilitate hierarchical routing in OSPF? |
the use of multiple areas |
In OSPF discussions what is used to
facilitate hierarchical routing in OSPF? |
the use of multiple areas |
The PRD company network engineer is
upgrading the Cisco IOS image on a Cisco ISR 4000 series. What command could
the engineer use to verify the total amount of flash memory as well as how
much flash memory is currently available? |
show flash0: |
Which combination of DTP modes set on
adjacent switches will cause the link to become an access link instead of a
trunk link? |
dynamic auto - dynamic auto |
In understanding IOS system image files what
statement describes a Cisco IOS image with the “universalk9_npe” designation
for Cisco ISR G2 routers? |
It is an IOS version that, at the request of
some countries, removes any strong cryptographic functionality. |
If you planning to built a large network
composed of datacenters, nationwide branches office, stores, remote overseas
offices which of these works better for larger network such as this? |
Multi-area OSPF |
When a customer purchases a Cisco IOS 15.0
software package, what serves as the receipt for that customer and is used to
obtain the license as well? |
Product Activation Key |
A connection to a switch went down suddenly,
how long can it take for a network using RSTP to converge again after a
topology change? |
6sec |
Among the 802.11 standards what is the
frequency assigned for 802.11g? |
2.4Ghz |
A CCIE network administrator is verifying a
multi-area OSPF configuration by checking the routing table on a router in
area 1. The administrator notices a route to a network that is connected to a
router in area 2. Which code appears in front of this route in the routing
table within area 1? |
O IA |
If a range of ports is being configured for
EtherChannel by the use of PAgP, which mode will form the bundled channel
only if the port receives PAgP packets from another device? |
auto |
A network specialist of Avengers Corporation
is troubleshooting an OSPFv2 network and discovers that two routers connected
by a point-to-point WAN serial link are not establishing an adjacency. The
OSPF routing process, network commands and area ID are all confirmed as
correct, and the interfaces are not passive. Testing shows that the cabling
is correct, that the link is up, and pings between the interfaces are
successful. What is most likely the problem? |
The subnet masks on the two connected serial
interfaces do not match. |
Based on the discussion in this chapter,
which command syntax will initiate EtherChannel interface configuration mode? |
interface port-channel interface-identifier |
In understanding multiarea OSPF network
which statement describes a multiarea OSPF network? |
It has a core backbone area with other areas connected
to the backbone area. |
Among the features of EIGRP which uses
multicast and unicast rather than broadcast? |
Less Overhead |
Among the listed below which is a feature of
EIGRP? |
Load balancing |
A CCIE network administrator is verifying a
multi-area OSPF configuration by checking the routing table on a router in
area 1. The administrator notices a route to a network that is connected to a
router in area 2. Which code appears in front of this route in the routing
table within area 1? |
O IA |
Which three steps in the design and
implementation of a multiarea OSPF network are considered planning steps?
(Choose a letter) |
2, 4 & 5 |
As discussed in this chapter, beginning with
the Cisco IOS Software Release 15.0, which license is a prerequisite for
installing additional technology pack licenses? |
DATA |
What is the function of PoE pass-through? |
allows switches, phones, and wireless access
points to receive power over existing Ethernet cables from an upstream switch |
Which two networks are part of the summary
route 192.168.32.0/22? (Choose a letter) |
2 & 3 |
The client of a networking company requires
VPN connectivity for workers who must travel frequently. To support the VPN
server, the customer router must be upgraded to a new Cisco IOS software
version with the Advanced IP Services feature set. What should the field
engineer do before copying the new IOS to the router? |
Issue the show version and the show flash
commands to ensure that the router has enough memory and file space to
support the new IOS image. |
What is the term that is used for the area
of a network that is affected when a device or network service experiences
problems? |
failure domain |
A newly hired network engineer has been
instructed to implement EtherChannel in a corporate network. What does this
configuration consist of? |
grouping multiple physical ports to increase
bandwidth between two switches |
In understanding of multiarea OSPF where do
inter-area route summarization be performed in an OSPF network? |
any router |
As discussed in this chapter, beginning with
the Cisco IOS Software Release 15.0, which license is a prerequisite for
installing additional technology pack licenses? |
IPBase |
Which switchport mode Puts the interface
into permanent trunking mode and negotiates |
switchport mode trunk |
As discussed in chapter 7 as one of the
EIGRP concepts what is the purpose of using protocol-dependent modules in
EIGRP? |
to accommodate routing of different network
layer protocols |
During summarization configuration what
address and wild card mask can be used to enable EIGRP for only the subnet
192.168.100.192 255.255.255.192? |
192.168.100.192 0.0.0.63 |
Which type of VLAN is identified by a VLAN
ID between 1006 and 4094 and not contained in updates of switches
participating in a VTP domain? |
extended |
What is a characteristic of out-of-band
device management? |
It requires a terminal emulation client. |
In wireless LAN standards what wireless LAN
technology that is an IEEE 802.15 WPAN standard; uses a device pairing
process to communicate over distance up to .05 mile (100m)? |
Bluetooth |
Which scalable method must be implemented in
order to provide inter-VLAN routing on a switched network with more than 1000
VLANs? |
routing traffic internally to a Layer 3 switch
device |
During network troubleshooting in MAX
Industries factory 2 routers, R1 and R2, have established an EIGRP neighbor
relationship, but there is still a connectivity problem. Which issue could be
causing this problem? |
An access list that is blocking the advertisements
from other networks was configured in each or both routers |
In wireless LAN technologies what wireless
LAN technology that operates in the range of a few hundred feet? |
WLAN |
During EIGRP operation which two EIGRP
packet types are sent with reliable delivery? |
Hello & Ack |
Among the 802.11 standards what is the
maximum speed of 802.11a? |
54Mb/s |
In understanding Cisco IOS image which
statement describes a difference between the IOS 15.0 extended maintenance
release and a standard maintenance release? |
The standard maintenance release enables faster
IOS feature delivery than the extended maintenance release does. |
A certified network administrator of RMS
Company has just changed the router ID on a router that is working in an
OSPFv2 environment. What should the administrator do to reset the adjacencies
and use the new router ID? |
Issue the clear ip ospf process privileged mode
command. |
As discussed in chapter 9 of Scaling
Networks what is the major release number in the IOS image name
c1900-universalk9-mz.SPA.152-3.T.bin? |
15 |
7. Which two networks are part of the
summary route 192.168.32.0/22? (Choose a letter) |
2 & 6 |
A certified network expert is configuring a
LAN with a redundant first hop to make better use of the available network
resources. Which protocol should the engineer implement? |
GLBP |
A newly hired certified network engineer of
RMS Industries is troubleshooting a switch and wants to verify if it is a
root bridge. Which of the following listed below is the right command to
display the correct information? |
show spanning-tree |
Understanding EtherChannel technology, what
is an advantage of using LACP? |
allows automatic formation of EtherChannel links |
A network administrator enters the following
command sequence on a Cisco 3560 switch. What is the purpose of these
commands? |
to make the Gi0/1 port a routed port |
As discussed in this chapter multiarea OSPF
what OSPF LSA type is used to inform routers of the router ID of the DR in
each multiaccess network in an OSPF area? |
type 1 |
During EIGRP operation where do successor
routes stored? |
in the routing table and the topology table |
Using LACP, besides of being a multivendor
protocol which among the listed below describes as it advantage? |
allows automatic formation of EtherChannel links |
A certified network administrator is trying
to add a new router into an established OSPF network. The networks attached
to the new router do not appear in the routing tables of the other OSPF
routers. Given the information in the partial configuration shown below, what
configuration error is causing this problem? |
The network wildcard mask is configured
improperly. |
A company has deployed four 48-port access
layer switches to a switch block. For redundancy each access layer switch
will connect to two distribution layer |
176 |
No comments:
Post a Comment